5.6 KiB
5.6 KiB
Cette page a été importée automatiquement de notre ancien wiki mais n'a pas encore été révisée.
Howto IPMI
http://www.intel.com/design/servers/ipmi/index.htm http://buttersideup.com/docs/howto/IPMI_on_Debian.html
modprobe ipmi_si
modprobe ipmi_devintf
ipmi message handler version 39.1
IPMI System Interface driver.
ipmi_si: Trying SMBIOS-specified kcs state machine at i/o address 0xca8, slave address 0x20, irq 0
ipmi: Found new BMC (man_id: 0x0002a2, prod_id: 0x0000, dev_id: 0x20)
IPMI kcs interface initialized
ipmi device interface
aptitude install openipmi
aptitude install ipmitool
cat /proc/devices | grep ipmi
NNN ipmidev
mknod -m 0600 /dev/ipmi0 c NNN 0
ipmitool lan print
ipmitool sensor
ipmitool sdr
over LAN :
usage: lan set <channel> <command> [option]
LAN set commands:
ipaddr <x.x.x.x> Set channel IP address
netmask <x.x.x.x> Set channel IP netmask
macaddr <x:x:x:x:x:x> Set channel MAC address
defgw ipaddr <x.x.x.x> Set default gateway IP address
defgw macaddr <x:x:x:x:x:x> Set default gateway MAC address
bakgw ipaddr <x.x.x.x> Set backup gateway IP address
bakgw macaddr <x:x:x:x:x:x> Set backup gateway MAC address
password <password> Set session password for this channel
snmp <community string> Set SNMP public community string
user Enable default user for this channel
access <on|off> Enable or disable access to this channel
arp response <on|off> Enable or disable BMC ARP responding
arp generate <on|off> Enable or disable BMC gratuitous ARP generation
arp interval <seconds> Set gratuitous ARP generation interval
auth <level> <type,..> Set channel authentication types
level = CALLBACK, USER, OPERATOR, ADMIN
type = NONE, MD2, MD5, PASSWORD, OEM
ipsrc <source> Set IP Address source
none = unspecified source
static = address manually configured to be static
dhcp = address obtained by BMC running DHCP
bios = address loaded by BIOS or system software
cipher_privs XXXXXXXXXXXXXXX Set RMCP+ cipher suite privilege levels
X = Cipher Suite Unused
c = CALLBACK
u = USER
o = OPERATOR
a = ADMIN
O = OEM
# ipmitool -I open lan set 1 "ipsrc" "static"
# ipmitool lan print 1
Set in Progress : Set In Progress
Auth Type Support : NONE MD2 MD5 PASSWORD
Auth Type Enable : Callback : MD2 MD5
: User : MD2 MD5
: Operator : MD2 MD5
: Admin : MD2 MD5
: OEM : MD2 MD5
IP Address Source : Static Address
IP Address : 0.0.0.0
Subnet Mask : 0.0.0.0
MAC Address : 00:13:72:50:42:42
SNMP Community String : public
IP Header : TTL=0x40 Flags=0x40 Precedence=0x00 TOS=0x10
=> interface Ethernet spécifique
<http://lonesysadmin.net/2007/06/21/how-to-configure-ipmi-on-a-dell-poweredge-running-red-hat-enterprise-linux/>
% ipmitool -I lan -H 1.2.3.169 -U root shell
bootdev <device> [clear-cmos=yes|no]
none : Do not change boot device order
pxe : Force PXE boot
disk : Force boot from default Hard-drive
safe : Force boot from default Hard-drive, request Safe Mode
diag : Force boot from Diagnostic Partition
cdrom : Force boot from CD/DVD
bios : Force boot into BIOS Setup
power :
cycle,reset = reboot
off,soft = extinction
on = demarrage
ipmitool shell
ipmitool> power status
Chassis Power is on
ipmitool> power cycle
Chassis Power Control: Cycle
ipmitool> user list
ID Name Callin Link Auth IPMI Msg Channel Priv Limit
2 root true true true ADMINISTRATOR
ipmitool> session info all
session handle : 32
slot count : 5
active sessions : 1
user id : 2
privilege level : ADMINISTRATOR
session type : IPMIv1.5
channel number : 0x01
console ip : 1.2.3.4
console mac : 00:16:17:52:fa:87
console port : 33594
ipmitool> sel list
7 | Pre-Init Time-stamp | Power Supply #0x65 | Power Supply AC lost | Asserted
8 | Pre-Init Time-stamp | Power Supply #0x74 | Redundancy Lost
9 | 08/17/2007 | 15:46:15 | Power Supply #0x65 | Failure detected | Deasserted
a | 08/17/2007 | 15:46:16 | Power Supply #0x65 | Power Supply AC lost | Deasserted
b | 08/17/2007 | 15:46:16 | Power Supply #0x74 | Fully Redundant
c | 08/17/2007 | 15:46:35 | Memory #0x53 | Correctable ECC | Asserted
d | 08/17/2007 | 15:46:42 | Temperature #0x30 | Upper Critical going high
e | 08/17/2007 | 15:46:46 | Temperature #0x30 | Upper Critical going high
f | 08/17/2007 | 15:46:49 | Voltage #0x60 | Lower Critical going low
modprobe ipmi_watchdog
IPMI Watchdog: driver initialized
Copyright (C) 2004 MontaVista Software - IPMI Powerdown via sys_reboot.
modprobe ipmi_poweroff
IPMI poweroff: ATCA Detect mfg 0x2A2 prod 0x100
IPMI poweroff: Found a chassis style poweroff function
IP :
----
ipmitool> lan set 1 ipaddr 1.2.3.33
Setting LAN IP Address to 1.2.3.33
ipmitool> lan set 1 netmask 255.255.255.0
Setting LAN Subnet Mask to 255.255.255.0
ipmitool> lan print 1
ipmitool> lan set 1 access on
Users :
-------
ipmitool> user set password 2 <password>
ipmitool> user test 2 16 <good-pass>
Success
ipmitool> user test 2 16 <bad-pass>
Set User Password command failed (user 2): Unknown (0x80)
Failure: password incorrect
En réseau :
===========
% ipmitool -I lan -H 1.2.3.169 -U root shell
OpenBSD :
=========
# sysctl hw.sensors