Relecture + remplacement IP par des IPs documentation RFC5737
This commit is contained in:
parent
5af83d3102
commit
e7a1f2bcaa
|
@ -626,7 +626,7 @@ Si souhaité, on peut sauvegarder le binaire actuel vers le serveur TFTP :
|
|||
|
||||
~~~
|
||||
Switch# copy flash:c2960-lanbasek9-mz.122-55.SE1.bin tftp:
|
||||
Address or name of remote host []? 192.168.0.20
|
||||
Address or name of remote host []? 192.0.2.20
|
||||
Destination filename [c2960-lanbasek9-mz.122-55.SE1.bin]?
|
||||
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
|
||||
9771282 bytes copied in 22.498 secs (434318 bytes/sec)
|
||||
|
@ -635,10 +635,10 @@ Destination filename [c2960-lanbasek9-mz.122-55.SE1.bin]?
|
|||
Ensuite, on récupère la version téléchargée du binaire sur le switch :
|
||||
|
||||
~~~
|
||||
Switch# copy tftp://192.168.0.20/c2960-lanbasek9-mz.122-55.SE12.bin flash:
|
||||
Switch# copy tftp://192.0.2.20/c2960-lanbasek9-mz.122-55.SE12.bin flash:
|
||||
Destination filename [c2960-lanbasek9-mz.122-55.SE12.bin]?
|
||||
Accessing tftp://192.168.0.20/c2960-lanbasek9-mz.122-55.SE12.bin...
|
||||
Loading c2960-lanbasek9-mz.122-55.SE12.bin from 192.168.0.20 (via Vlan1): !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
|
||||
Accessing tftp://192.0.2.20/c2960-lanbasek9-mz.122-55.SE12.bin...
|
||||
Loading c2960-lanbasek9-mz.122-55.SE12.bin from 192.0.2.20 (via Vlan1): !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
|
||||
[OK - 9827106 bytes]
|
||||
|
||||
9827106 bytes copied in 125.502 secs (78302 bytes/sec)
|
||||
|
@ -715,7 +715,7 @@ Delete flash:c2960-lanbasek9-mz.122-55.SE1.bin? [confirm]
|
|||
~~~
|
||||
Switch# configure terminal
|
||||
Switch(config)# interface Vlan 1
|
||||
Switch(config-if)# ip address 192.168.0.10 255.255.255.0
|
||||
Switch(config-if)# ip address 192.0.2.10 255.255.255.0
|
||||
~~~
|
||||
|
||||
#### Créer un VLAN
|
||||
|
@ -849,7 +849,7 @@ Configuration IP de base :
|
|||
~~~
|
||||
Switch# conf t
|
||||
(config)# interface Vlan1
|
||||
(config-if)# ip address 192.168.0.1 255.255.255.0
|
||||
(config-if)# ip address 192.0.2.1 255.255.255.0
|
||||
(config-if)# no shutdown
|
||||
~~~
|
||||
|
||||
|
@ -1535,21 +1535,21 @@ Il peut permettre par exemple de rapidement exécuter des pings à de multiples
|
|||
~~~
|
||||
Switch# tclsh
|
||||
Switch(tcl)# foreach address {
|
||||
+> 192.168.0.3
|
||||
+> 192.168.0.4
|
||||
+> 192.168.0.5
|
||||
+> 192.0.2.3
|
||||
+> 192.0.2.4
|
||||
+> 192.0.2.5
|
||||
+> } { ping $address repeat 3 }
|
||||
|
||||
Type escape sequence to abort.
|
||||
Sending 3, 100-byte ICMP Echos to 192.168.0.3, timeout is 2 seconds:
|
||||
Sending 3, 100-byte ICMP Echos to 192.0.2.3, timeout is 2 seconds:
|
||||
!!!
|
||||
Success rate is 100 percent (3/3), round-trip min/avg/max = 5/10/21 ms
|
||||
Type escape sequence to abort.
|
||||
Sending 3, 100-byte ICMP Echos to 192.168.0.4, timeout is 2 seconds:
|
||||
Sending 3, 100-byte ICMP Echos to 192.0.2.4, timeout is 2 seconds:
|
||||
!!!
|
||||
Success rate is 100 percent (3/3), round-trip min/avg/max = 1/7/15 ms
|
||||
Type escape sequence to abort.
|
||||
Sending 3, 100-byte ICMP Echos to 192.168.0.5, timeout is 2 seconds:
|
||||
Sending 3, 100-byte ICMP Echos to 192.0.2.5, timeout is 2 seconds:
|
||||
!!!
|
||||
Success rate is 100 percent (3/3), round-trip min/avg/max = 1/2/5 ms
|
||||
~~~
|
||||
|
@ -1593,12 +1593,12 @@ Le serveur DHCP pourra être dans un VLAN dédié.
|
|||
|
||||
Pour activer le DHCP Relay, sur chaque interface VLAN, rajouter la directive `ip address helper <ip-server-dhcp>`.
|
||||
|
||||
Voici un exemple de création d'un VLAN avec l'adresse 192.168.200.1/24, faisant office de DHCP relay pour le serveur 10.0.1.2 :
|
||||
Voici un exemple de création d'un VLAN avec l'adresse 192.0.2.50/24, faisant office de DHCP relay pour le serveur 198.51.100.2 :
|
||||
|
||||
~~~
|
||||
Switch(config)# interface vlan 200
|
||||
Switch(config-if)# ip address 192.168.200.1 255.255.255.0
|
||||
Switch(config-if)# ip helper-address 10.0.1.2
|
||||
Switch(config-if)# ip address 192.0.2.50 255.255.255.0
|
||||
Switch(config-if)# ip helper-address 198.51.100.2
|
||||
Switch(config-if)# end
|
||||
~~~
|
||||
|
||||
|
@ -1671,7 +1671,7 @@ Switch# show interface e1/1 trunk
|
|||
Switch# conf t
|
||||
Switch(config)# feature interface-vlan
|
||||
Switch(config)# interface Vlan 1
|
||||
Switch(config-if)# ip address 192.168.0.10/24
|
||||
Switch(config-if)# ip address 192.0.2.10/24
|
||||
Switch(config-if)# no shutdown
|
||||
~~~
|
||||
|
||||
|
@ -2115,7 +2115,7 @@ Active-image: flash://system/images/image1.bin
|
|||
MD5 Digest: 07968d912499cff5e8b07fdc24779854
|
||||
~~~
|
||||
|
||||
On choisit la version souhaité, et on télécharge le binaire.
|
||||
On choisit la version souhaitée, et on télécharge le binaire.
|
||||
|
||||
Ensuite, on peut mettre à jour le switch de 2 manières différentes.
|
||||
|
||||
|
@ -2123,11 +2123,11 @@ Ensuite, on peut mettre à jour le switch de 2 manières différentes.
|
|||
|
||||
On se connecte à l'interface web du switch, puis on va dans le menu Administration > File Management > Firmware Operations.
|
||||
|
||||
Si souhaité, on peut sauvegarder le binaire actuel en sélectionner "Backup Firmware" pour Operation Type", et "HTTP/HTTPS" pour "Copy Method", puis le téléchargement débute.
|
||||
Si souhaité, on peut sauvegarder le binaire actuel en sélectionnant "Backup Firmware" pour Operation Type", et "HTTP/HTTPS" pour "Copy Method", puis le téléchargement débute.
|
||||
|
||||
Pour la mise à jour, on sélectionne "Update Firmware" pour "Operation Type", et "HTTP/HTTPS" pour "Copy Method".
|
||||
|
||||
On clique sur "Browse...", on sélectionne le binaire téléchargé précédemment, et on cliqu sur "Apply".
|
||||
On clique sur "Browse...", on sélectionne le binaire téléchargé précédemment, et on clique sur "Apply".
|
||||
|
||||
À la fin, l'interface web indique que l'opération a été terminée avec succès.
|
||||
|
||||
|
@ -2175,8 +2175,8 @@ On configure le serveur sur l'utilisateur `nobody`, et on ajoute l'option `-c` p
|
|||
Si souhaité, on peut sauvegarder le binaire actuel vers le serveur TFTP :
|
||||
|
||||
~~~
|
||||
Switch# copy flash://system/images/image1.bin tftp://192.168.0.20/old-binary.bin
|
||||
%COPY-I-FILECPY: Files Copy - source URL flash://system/images/image1.bin destination URL tftp://192.168.0.20/old-binary.bin
|
||||
Switch# copy flash://system/images/image1.bin tftp://192.0.2.20/old-binary.bin
|
||||
%COPY-I-FILECPY: Files Copy - source URL flash://system/images/image1.bin destination URL tftp://192.0.2.20/old-binary.bin
|
||||
%COPY-W-TRAP: The copy operation was completed successfully
|
||||
|
||||
Copy: XXX bytes copied in 00:04:27 [hh:mm:ss]
|
||||
|
@ -2185,8 +2185,8 @@ Copy: XXX bytes copied in 00:04:27 [hh:mm:ss]
|
|||
Ensuite, on récupère la version téléchargée du binaire sur le switch :
|
||||
|
||||
~~~
|
||||
Switch# boot system tftp://192.168.0.20/image_tesla_hybrid_2.5.9.54_release_cisco_signed.bin
|
||||
%COPY-I-FILECPY: Files Copy - source URL tftp://192.168.0.20/image_tesla_hybrid_2.5.9.54_release_cisco_signed.bin destination URL flash://system/images/image_tesla_hybrid_2.5.9.54_release_cisco_signed.bin
|
||||
Switch# boot system tftp://192.0.2.20/image_tesla_hybrid_2.5.9.54_release_cisco_signed.bin
|
||||
%COPY-I-FILECPY: Files Copy - source URL tftp://192.0.2.20/image_tesla_hybrid_2.5.9.54_release_cisco_signed.bin destination URL flash://system/images/image_tesla_hybrid_2.5.9.54_release_cisco_signed.bin
|
||||
%COPY-W-TRAP: The copy operation was completed successfully
|
||||
|
||||
Copy: XXX bytes copied in 00:04:27 [hh:mm:ss]
|
||||
|
|
Loading…
Reference in a new issue